Air Monitor VELTRON DPT 2500-plus Скачать руководство пользователя страница 28

Страница: 28 / 36

VELTRON DPT 2500-

plus

Air Monitor Corporation

116-047-20.PMD (5/5/11)

VELTRON DPT 2500-

plus

- IO&M Manual

SECTION 6 – CALIBRATION

6.3 – TRANSMITTER INPUT CALIBRATION

6.3.1

For Units With Positive or Negative Differential Pressure Spans.

Zero pressure and transducer natural sp

n pressure will be applied to the VE

RON DPT 2500-

plus

, unit will be

programmed to recognize these pressures as zero and span for transmitter input calibration.

1. While in Main Menu, scroll to:

Transmitter Input

Calibration

2. Press , and display will indicate:

Input Zero Calib.

3. Press , and display will indicate:

Input Zero Calib.

-- Push ENTER --

4. Slide switch S1 - "AZ V

lve" to the ON position.

5. Press , and display will indicate:

Transducer Zero

Settle Time:4

Display will count down to 0, after which it will indicate: Input Zero Done

-- Push ESCAPE --

Display will count down to 0, after which it will indicate: Input Span Done

-- Push ESCAPE --

Note: If pressure input is less than 40% or greater than 1

0% of transducer's Natural s

n value (see

Factory Set-Up Information Sheet), display will indicate:

Bad Input S

-- Push ESCAPE --

If this occurs, check input pressure (as read on manometer), and readjust as necessary

Press and

repeat S

eps 7 through 10.

11. Remove input pressure from High port on VELTRON DPT 2500-

plus

12. Press and then , display will indicate: Return to

MAIN MENU

13. Press , and display will return to Main Menu.

6. Press and then , display will indicate:

Input S

an Calib.

7. Press , and display will indicate:

Input Span Calib.

-- Push ENTER --

8. Slide switch S1 - "AZ Valve" to the OFF position.

9. Apply input pressure (as read on manometer) to the High port of the VE

RON DPT 2500-

plus

. Adjust

pressure to equal the transducer natural s

n value (see Factory Set-Up Information Sheet for this value).

10. Press , and display will indicate:

Transducer Span

Settle Time:4

Содержание VELTRON DPT 2500-plus





































Результаты поиска

Содержание VELTRON DPT 2500-plus

Отзывы:

Бренды по названию

Популярные бренды

Air Monitor VELTRON DPT 2500-plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание VELTRON DPT 2500-plus

Отзывы:

Бренды по названию

Популярные бренды