Air Monitor VELTRON DPT 2500-plus Скачать руководство пользователя страница 24

Страница: 24 / 36

VELTRON DPT 2500-

plus

Air Monitor Corporation

116-047-20.PMD (5/5/11)

VELTRON DPT 2500-

plus

- IO&M Manual

5.9 – AUTO-zero CONFIGURATION

User can turn AUTO-zero function ON or OFF, and select activation interval.

1. While in Main Menu, use or to scroll to:

Auto-Zero

Configuration

2. Press to enter

UTO-zero Configuration menu. Display will indicate: Auto-Zero Off/On

Selection

3. Press and display will indicate current setting of

UTO-zero (OFF or ON).

4. Use or to change setting. Once desired setting is displayed, press , new setting will be stored in

memory and display will return to

UTO-zero Configuration menu as in S

ep 2.

Note: If user desires not to change the setting and return to

UTO-zero Configuration menu press . Unit

will remain programmed as it was originally.

5. Use or to select remaining p

rameters to be changed.

6. Follow Step 4 to make any changes to p

rameters.

7. To return to Main Menu select Return to MAIN MENU in

UTO-zero Configuration menu and press .

SECTION 5 – OPERATION

Auto-Zero Off/On

Default selection shown.

Available selections:

ON or OFF

- Auto-Zero Off/On Selection

- Auto-Zero Interval Selection

- Return to MAIN MENU

Auto-Zero Interval

1 Hour

1 to 24 hours

in 1 hr. increments

User Setup Main Menu

Auto-Zero Configuration

Return to

MAIN MENU

- Low Pass Filter Selection



Auto-Zero Configuration

- Transducer Span Selection

Available selections:

Содержание VELTRON DPT 2500-plus





































Результаты поиска

Содержание VELTRON DPT 2500-plus

Отзывы:

Бренды по названию

Популярные бренды

Air Monitor VELTRON DPT 2500-plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание VELTRON DPT 2500-plus

Отзывы:

Бренды по названию

Популярные бренды