manualshive.com logo in svg

Air Monitor VELTRON DPT 2500-plus, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Air Monitor VELTRON DPT 2500-plus Скачать руководство пользователя страница 19

VELTRON DPT 2500-

plus

Air Monitor Corporation

116-047-20.PMD (5/5/11)

VELTRON DPT 2500-

plus

 - IO&M Manual

5.7 – TRANSMITTER SCALING & CONFIGURATION (con't)

1. While in Main Menu, use       or       to scroll to:

             Transmitter Scaling

               and Configuration

2. Press       to enter Transmitter Scaling & Configuration menu. Display will indicate:        Square Root On/Off

      Configuration

3. Press       and display will indicate current setting of Square Root (OFF or ON).

4. Use       or       to change setting.  Once desired setting is displayed, press      , new setting will be stored in

memory and display will return to Transmitter Scaling & Configuration menu as in S

t

ep 2.

Note:  If user desires not to change the setting and return to the Transmitter Scaling & Configuration sub-menu,

press      .  Unit will remain programmed as it was originally.

5. Use       or       to select remaining p

a

rameters to be changed within the Process Configuration sub-menu.

See the following Unit

s

 Lists for the available Process Unit

s

 selections for the appropriate Process T

y

pe.

See the following Format List for the available Process Format selections.

6. Follow S

t

ep 4 to make any changes to parameters.

7. To return to the Main Menu, select Return to Main Menu in the T

r

ansmitter Scaling & Configuration menu and

press      .

Note: If Process Minimum is selected to be a value greater than zero (0), Output will not increase until the actual

process exceeds this selected value.  This is known as "Zero Suppression".

Zero Suppression (Process Minimum) can be set up to 60% of the Process Maximum selected.

Display of process is not af

f

ected by this selection, and will indicate the actual process value.

14

SECTION 5 – OPERATION

X

Содержание VELTRON DPT 2500-plus





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды