Air Monitor VELTRON DPT 2500-plus Скачать руководство пользователя страница 29

Страница: 29 / 36

VELTRON DPT 2500-

plus

Air Monitor Corporation

116-047-20.PMD (5/5/11)

VELTRON DPT 2500-

plus

- IO&M Manual

SECTION 6 – CALIBRATION

6.3 – TRANSMITTER INPUT CALIBRATION (con't)

6.3.2

For Units With Bi-Polar Spans.

Minimum and maximum transducer natural sp

n pressure will be applied to the VELTRON DPT 2500-

plus

, unit

will be programmed to recognize these pressures as zero and sp

n for transmitter input calibration.

1. Connect input pressure to Low

ort of VE

RON DPT 2500-

plus

Transmitter Input

2. While in Main Menu, scroll to:

Calibration

3. Press , and display will indicate:

Input Zero Calib.

4. Press , and display will indicate:

Input Zero Calib.

-- Push ENTER --

5. Slide switch S1 - "AZ V

ve" to the OFF position.

6. Apply input pressure (as read on manometer) to the Low Port of the VE

RON DPT 2500-

plus

Adjust pressure to equal the positive equivalent of the minimum (negative) transducer natural sp

value (see Factory Set-Up Information Sheet for this value).

7. Press , and display will indicate:

Transducer Zero

Settle Time:4

Display will count down to 0, after which it will indicate: Input Zero Done

-- Push ESCAPE --

8. Press and then , display will indicate:

Input S

an Calib.

9. Press , and display will indicate:

Input S

an Calib.

-- PUSH ENTER --

10. Connect input pressure to the High Port of the VELTRON DPT 2500-

plus

11.Apply input pressure (as read on manometer) to the High Port of the VE

RON DPT 2500-

plus

Adjust pressure to equal the maximum (positive) transducer natural sp

n value (see Factory Set-Up

Information Sheet for this value).

12. Press , and display will indicate:

Transducer Span

Settle Time:4

Display will count down to 0, after which it will indicate: Input S

an Done

-- Push ESCAPE --

Note: If pressure input is less than 40% or greater than 1

0% of transducer's maximum (positive)

Natural span value range (see Factory Set-Up Information Sheet), display will indicate:

Bad Input S

-- Push ESCAPE --

If this occurs, check input pressure (as read on manometer), and readjust as necessary

Press and

repeat S

eps 9 through 12.

Содержание VELTRON DPT 2500-plus





































Результаты поиска

Содержание VELTRON DPT 2500-plus

Отзывы:

Бренды по названию

Популярные бренды

Air Monitor VELTRON DPT 2500-plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание VELTRON DPT 2500-plus

Отзывы:

Бренды по названию

Популярные бренды