Aero AeroForce F2B Скачать руководство пользователя страница 28

Страница: 28 / 30

AeroForce F2B

AeroForce F2B Manual Model

Maintenance Recommendations

Aero Industries recommends a weekly inspection of the following items:

IMPORTANT:

Replace all worn or broken parts immediately. Repairs must ONLY be made after

proper instruction.

Inspect Tarp for wear and tears.

Inspect Arms for damage (cracked, dented or bent).

Bearings: Pull the shafts from side to side and in and out. If there is excessive play, replace the bearings. Apply

penetrating oil lightly as needed.

Springs: Examine springs for breakage or distortion. Apply a light coat of penetrating oil to tension springs as needed.

Fasteners: Make sure all mounting bolts and nuts are in place and tight and that no parts are worn or damaged.

Chain:

Check the chain tension, that links move smoothly, and make sure the master link is on. Lubricate the chain

regularly with penetrating oil.

Electrical Connections:

Check all electrical connections and tighten any that have become loose.

Safety Labels: Clean labels with soap and water. Replace if damaged and/or difficult to read.

Replacement Parts and instructions may be obtained from your Aero dealer or by contacting Aero Industries.

Crank handle is only used for uncovering. Remove and store crank handle when not in

use.

Face vehicle into the wind during operation. Wind may cause tarp to sail and damage system.

Uncover Unit

(Standard Crank)

Uncover Unit

(Reverse Crank)

Crank handle is only
used for uncovering.
Remove and store
crank handle when
not in use.

Cover Unit

Keep brake handle engaged to provide

braking action while releasing (covering) the tarp. If handle
is released too soon while covering, damage may occur.

Pull brake handle down
quickly to brake position

Содержание AeroForce F2B































Результаты поиска

Содержание AeroForce F2B

Отзывы:

Похожие инструкции для AeroForce F2B

Бренды по названию

Популярные бренды

Aero AeroForce F2B, Руководство по установке

Результаты поиска

Содержание AeroForce F2B

Отзывы:

Похожие инструкции для AeroForce F2B

Бренды по названию

Популярные бренды