Aero AeroForce F2B Скачать руководство пользователя | Manualshive

Страница: 13 / 30

background image

13

AeroForce F2B

Installation Instructions

Step 3c

Installing the Chain and Chain Cover(s)

1) Figure 13-1.

Wrap chain (1) around both sprockets and

remove the excess links.

2)

Wrap the shortened chain the sprockets and fasten the

two ends with the master link (2).

NOTE:

To remove any slack in the chain, loosen

the crank the crank assembly mounting bolts and
slide the crank assembly away from the tarp roll up
bar. The chain should be snug but not overly tight.
Retighten the Mounting bolts.

Index Description

Qty

1

Chain

1

2

Master Link

1

3

Crank Cover Aluminum

1

4

Chain Cover Lower Aluminum

1

Index Description

Qty

5

Guard Mounting Brackets

6

6

#14 x 1/2 Self Drilling Screw

6

7

#14 x 1 Self Drilling Screw

6

8

Crank Handle

1

Aluminum Cover

3) Figure 13-2.

Install crank cover lower aluminum (4)

with the guard mounting brackets (5) to the body with
#14 x 1/2 self drilling screws (6) and #14 x 1 self
drilling screw (7).

4) Figure 13-3.

Position the chain cover aluminum (3) so that it lays over the top edge of crank cover lower

aluminum (4). Adjust the chain cover aluminum (3) so that it clears the chain and sprocket evenly on both
sides and clears the top by 1".

NOTE:

The crank handle is used to move the tarp forward. The crank handle should be removed

once the tarp is properly positioned.



3

4

5

6

7

8









Figure 13-1

Figure 13-2

Figure 13-3

«
...
11
12
13
14
15
...
»

Содержание AeroForce F2B































Отзывы:

Нет отзывов

Похожие инструкции для AeroForce F2B

Бренд: U-Line Страницы: 15

Бренд: Paccar Страницы: 212

T-MAG XC Series

Бренд: Mag International Страницы: 107

Бренд: MAFI Страницы: 142

Бренд: MAFI Страницы: 152

Бренд: Volvo Страницы: 244

Бренд: Volvo Страницы: 256

Бренд: Volvo Страницы: 300

Бренд: Kleton Страницы: 8

Бренд: Kleton Страницы: 8

Бренд: Kleton Страницы: 8

Бренд: Case Страницы: 51

BUSINESS CLASS M2 100

Бренд: freightliner Страницы: 198

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды