AEQ PHOENIX ALIO Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 91

AEQ PHOENIX ALIO Скачать руководство пользователя страница 47

AEQ

PHOENIX ALIO

47

AEQ PHOENIX Audiocodecs (Mercury, Venus, Studio, Stratos and ALIO) can connect to up to
3  SNMP  clients,  installed  in  remote  PCs,  by  simply  configuring  their  IP  addresses  in  the
"SNMP"  tab  of  previous  menu.  Once  one  or  more  SNMP  clients  are  connected  and  the
corresponding  "MIB"  descriptive  file  has  been  loaded  (it  can  be  downloaded  from  the
equipment's  Web  Interface:  see  section  7.8  of  this  manual),  the  audiocodec  will  send/accept
different types of informations to/from each client:

1. Alarms (Traps): Provide information relating to certain equipment's events that can be
considered as alarms. They usually have two possible states: Active or Inactive. The list of
alarms defined for Phoenix ALIO is as follows:

-

phxCh1NoTxAudioAlarm (Audio detection event at Channel 1's input)

-

phxCh1NoRxAudioAlarm (Audio detection event at Channel 1's output)

-

phxCh2NoTxAudioAlarm (Audio detection event at Channel 2's input)

-

phxCh2NoRxAudioAlarm (Audio detection event at Channel 2's output)

-

phxCh1NoAudioSyncAlarm (Sync event at Channel 1 while connected)

-

phxCh2NoAudioSyncAlarm (Sync event at Channel 2 while connected)

-

phxCh1CallEndAlarm (Call ended on Channel 1 due to incoming RTP traffic loss)

-

phxCh2CallEndAlarm (Call ended on Channel 2 due to incoming RTP traffic loss)

-

phxOtherAlarm (Other alarms, see name) -> Fail to register in SIP PROXY server,
activation / deactivation of BACKUP interface for Ch1 and/or Ch2.

-

coldStart alarm (Starting from unit off. This is a standard SNMP alarm, it appears only
one time and has no activation or deactivation).

These alarms are sent whenever they change, but we can choose from the SNMP client which
ones are shown / treated and which not.

The  first  4  audio  alarms  are  configurable  and  they  are  activated  whenever  the  incoming  or
outgoing (depending on the particular alarm) audio level is below a certain threshold for a given
time,  parameters  that  are  set  either  by  means  of  the  Control  Phoenix  software,  or  using  the
following  SET  commands.  For  example,  alarm  "phxCh1NoTxAudioAlarm"  will  become  Active
whenever  audio  from  ch1  input  has  a  level  below  the  threshold  defined  by
"phxCh1TxAudioThreshold" during a longer time than specified by "phxCh1TxAudioInterval".

2. Configurations (SET): adjustments related to some of the above defined alarms (the SNMP
client will configure them by means of "SET" commands, although in the case of Phoenix units,
they can also be modified by means of "AEQ ControlPHOENIX" remote control software):

-

phxCh1TxAudioThreshold (Audio threshold for channel 1's input)

-

phxCh1TxAudioInterval (Audio interval for channel 1's input)

-

phxCh1RxAudioThreshold (Audio threshold for channel 1's output)

-

phxCh1RxAudioInterval (Audio interval for channel 1's output)

«
...
45
46
47
48
49
...
»

Содержание PHOENIX ALIO




























































































Отзывы:

Нет отзывов