manualshive.com logo in svg

Advanced Instruments OsmoTECH XT, Руководство пользователя

Поделиться
Скачать
Advanced Instruments OsmoTECH XT Скачать руководство пользователя страница 9

10

OsmoTECH XT Single-Sample Micro-Osmometer User Guide

Safe use

WARNING: To reduce the risk of bodily injury, electric shock, fire, and damage to your instrument, please read and observe 
all precautions in this User Guide.

Only operate this product in accordance with the equipment design, operating instructions, and manufacturer 
recommendations; to do otherwise may impair the instrument function or create a safety hazard.

Do not attempt to perform electrical work if you are not fully qualified. This manual is not a substitute for electrical 
training.

General cautions

• 

Only power this instrument with the source specified 
on the product electrical ratings label. Refer to the 
installation instructions.

• 

If the power cord provided is replaced for any reason 
or if an alternate cord is used, the cord must be 
approved for use in the local country. The power cord 
must be approved for the product listed operating 
voltage and be rated at least 20% greater than the 
volt-ampere (VA) ratings marked on the product’s 
electrical ratings label. The cord end that connects to 
the product must have an IEC 60320 connector.

• 

Plug the product into an approved grounded electrical 
outlet. Exposure to AC voltage could lead to electric 
shock, burn or electrocution. Please be aware of any 
exposure of AC voltage in the power cord. 

• 

Do not disable the power cord grounding pin.

• 

If an extension cord or power strip is used, make sure 
that the cord or strip is rated for the product, and that 
the total ampere ratings of all products plugged into 
the extension cord or strip do not exceed 80% of the 
cord or strip rating limit.

• 

Route power cords so that they will not be walked on, 
tripped on, or pinched by items placed upon or 
against them. Pay particular attention to the plug, 
electrical outlet, and the point where the cord exits the 
product.

• 

Do not pull on cords and cables; grasp the 
corresponding connector to unplug it.

• 

Do not install or use this product in any area subject to 
extreme short-term temperature variations, or 
locations that exceed the specified operating 
environment temperatures.

• 

Never use this product in a wet area.

• 

To avoid injury or fire hazard, do not operate this 
product in an explosive atmosphere.

• 

Do not install or use the product on an unstable, 
non-level work surface.

• 

Do not operate this product with the covers removed 
or unsecured.

Содержание OsmoTECH XT


































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды