manualshive.com logo in svg

Advance acoustic SC3000 26" Disc, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic SC3000 26

GENERAL INFORMATION

SERVICE MANUAL

ENGLISH

SC3000 26” Disc 

9099052000

3

GENERAL INFORMATION

CONVENTIONS

Forward, backward, front, rear, left or right are intended with reference to the operator’s position, that is to say in driving position.

MACHINE LIFTING

WARNING!

Do not work under the lifted machine without supporting it with safety stands.

MACHINE TRANSPORTATION

WARNING!

Before transporting the machine, make sure that:

All covers are closed.

 

–

The ignition key is removed.

 

–

The machine is securely fastened to the means of transport.

 

–

OTHER REFERENCE MANUALS

The following manuals are available at Nilfisk Literature Service Department:

SC3000 Operator manual - Form Number 9098828000

 

–

SC3000 Spare Parts List - Form Number 9098828000

 

–

24V 670W Motor Installation Instructions - Form Number 9098456000

 

–

SAFETY

The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary 

precautions to safeguard people and property.

SYMBOLS

DANGER!

It indicates a dangerous situation with risk of death for the operator.

WARNING!

It indicates a potential risk of injury for people or damage to objects.

CAUTION!

It indicates a caution related to important or useful functions.

Pay careful attention to the paragraphs marked by this symbol.

NOTE

It indicates a remark related to important or useful functions.

CONSULTATION

It indicates the necessity to refer to the Operator manual before performing any procedure.

A2 ENGLISH(2).indd   3

29/07/2011   17.02.31

Содержание SC3000 26" Disc







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды