manualshive.com logo in svg

Advance acoustic SC3000 26" Disc, Руководство по обслуживанию, Страница: 25 / 70

Поделиться
Скачать
Advance acoustic SC3000 26

BRUSHING SYSTEM

SERVICE MANUAL

ENGLISH

SC3000 26” Disc 

9099052000

23

BRUSH DECK ADJUSTER SPRING DISASSEMBLY/ASSEMBLY

Disassembly

Drive the machine on a level floor.

1. 

Remove the brush/pad-holder deck (see the procedure in the relevant paragraph).

2. 

Turn the ignition key to “0” and disconnect the batteries.

3. 

Remove the front fairing (see the procedure in the relevant paragraph).

4. 

Place a wooden shim (A) under the deck holder assembly. Wooden shim thickness must be 160 mm.

5. 

Unscrew the ring nut (B), recover the washer, then carefully remove the spring (C).

6. 

If necessary, replace the spring taking care to properly place the elastic ends (D) on the frame.

7. 

Assembly

Assemble the components in the reverse order of disassembly, and note the following:

8. 

Tighten the ring nut (B) so that the deck holder assembly can turn freely.

• 

A

B

C

D

P100382

A2 ENGLISH(2).indd   23

29/07/2011   17.02.54

Содержание SC3000 26" Disc







































































Отзывы:

Нет отзывов