manualshive.com logo in svg

Advance acoustic SC3000 26" Disc, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic SC3000 26

PARKING BRAKE SYSTEM

SERVICE MANUAL

ENGLISH

SC3000 26” Disc 

9099052000

35

PARKING BRAKE SYSTEM

ELECTROMAGNETIC BRAKE DISASSEMBLY/ASSEMBLY

Disassembly

Place the machine on a hoisting system (if available), then lift it. Otherwise, drive the machine on a level floor.

1. 

Lower the brush deck.

2. 

Turn the ignition key to “0” and disconnect the batteries.

3. 

Turn the steering wheel to reach the electromagnetic brake.

4. 

On the left side of the machine, remove the screws (A) and disconnect the connector (B).

5. 

Remove the electromagnetic brake (C).

6. 

Assembly

Assemble the components in the reverse order of disassembly, and note the following:

7. 

Before installing the electromagnetic brake (C) clean it with compressed air.

• 

Install the electromagnetic brake with the lever (D) downwards.

• 

After installing the electromagnetic brake check the parking brake.

8. 

A

D

C

B

P100388

A2 ENGLISH(2).indd   35

29/07/2011   17.02.59

Содержание SC3000 26" Disc







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды