manualshive.com logo in svg

Advance acoustic SC3000 26" Disc, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic SC3000 26

RECOVERY WATER SYSTEM

SERVICE MANUAL

ENGLISH

SC3000 26” Disc 

9099052000

31

SQUEEGEE LIFTING CABLE DISASSEMBLY/ASSEMBLY

Disassembly

Remove the squeegee lifting assembly (see the previous paragraph, steps 1 to 6).

1. 

At the workbench, remove the screw (A) and recover the nut.

2. 

Carefully remove the squeegee lifting cable (B) from the pulleys.

3. 

Assembly

Install the lifting cable and note the following:

4. 

Grease the cable along its entire length with AGIP GR 30 or equivalent grease.

• 

Insert the cable in the direction shown by the arrow (C).

• 

Route the cable in the pulleys (D), (E) and (F) in sequence.

• 

Fasten the cable grommet with the screw (A) and nut.

• 

The components must be carefully installed as shown in the figure for the proper operation of the lifting system.

5. 

Install the squeegee lifting assembly (see the previous paragraph).

6. 

Check the proper operation of the squeegee lifting system.

7. 

NOTE

The squeegee lifting system pulleys are self-lubricating and do not require maintenance.

A

B

D

E

F

A

D

C

E

F

Front

Front

P100386

A2 ENGLISH(2).indd   31

29/07/2011   17.02.58

Содержание SC3000 26" Disc







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды