Advance acoustic SC3000 26" Disc Скачать руководство пользователя страница 17

Страница: 17 / 70

ECOFLEX™ SYSTEM

SERVICE MANUAL

ENGLISH

SC3000 26” Disc

9099052000

ECOFLEX™ SYSTEM

DETERGENT PUMP AND ONE-WAY VALVE DISASSEMBLY/ASSEMBLY

Disassembly

Place the machine on a hoisting system (if available), then lift it. Otherwise, drive the machine on a level floor.

Lower the brush deck.

Turn the ignition key to “0” and disconnect the batteries.

Open the detergent tank plug (42).

On the left side of the machine, remove the screws and nuts (A).

Disconnect the connectors (B) and (C).

Disconnect the hose (D).

Remove the detergent pump (E).

If necessary, remove the retaining springs (F) and disconnect the one-way valve (G) from the relevant hoses.

Assembly

Assemble the components in the reverse order of disassembly, and note the following:

10.

Connect the connector with black cable (B) and white cable (C) as shown in the figure.

•

Install the one-way valve (G) with the arrow (H) turned in the direction of the detergent flow.

•

P100375

P100376

A2 ENGLISH(2).indd 15

29/07/2011 17.02.46

Содержание SC3000 26" Disc







































































Результаты поиска

Содержание SC3000 26" Disc

Отзывы:

Похожие инструкции для SC3000 26" Disc

Бренды по названию

Популярные бренды

Advance acoustic SC3000 26" Disc, Руководство по обслуживанию

Результаты поиска

Содержание SC3000 26" Disc

Отзывы:

Похожие инструкции для SC3000 26" Disc

Бренды по названию

Популярные бренды