manualshive.com logo in svg

Advance acoustic SC3000 26" Disc, Руководство по обслуживанию

Поделиться
Скачать
Advance acoustic SC3000 26

SOLUTION/CLEAN WATER SUPPLY SYSTEM

ENGLISH

SERVICE MANUAL

14

9099052000

SC3000 26” Disc

TROUBLESHOOTING

Small amount of solution or no solution reaches the brush

Possible causes:

The tank filter (optional) is clogged/dirty (clean).

1. 

The solution filter is clogged/dirty (clean).

The solution tap is closed/semi-closed (replace).

2. 

The solenoid valve (EV1) is broken or there is an open in the electrical connection (replace the solenoid valve/repair the 

3. 

electrical connection).

There is debris in the solution/clean water tank clogging the output hole (clean the tank).

4. 

There is debris in the solution/clean water hoses clogging the flow (clean the hoses).

5. 

The function electronic board (EB1) is faulty (replace).

6. 

The display electronic board (EB2) is faulty (replace).

7. 

The dashboard electronic board (EB3) is faulty (replace).

8. 

The solution reaches the brush also when the machine is off

Possible causes:

There is dirt or calcium deposit on the solenoid valve gasket (clean).

1. 

The solenoid valve is broken (replace).

2. 

WIRING DIAGRAM

P100374A

A2 ENGLISH(2).indd   14

29/07/2011   17.02.45

Содержание SC3000 26" Disc







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды