manualshive.com logo in svg

ADEMCO VIDEO RapidView, Руководство по эксплуатации

Поделиться
Скачать
ADEMCO VIDEO RapidView Скачать руководство пользователя страница 5

Rapid View                                                                                              Operation Guide

Page iv                                                     © Ademco Video 2002 MNRDVO250602US

Safety 
Notes

Connection to the mains supply

Reference should be made to national wiring rules:

WARNING The mains supply should only be connected by 
a technically competent person and according to the         
current IEE wiring regulations.

For permanently connected equipment: “a readily accessible 
disconnect device shall be incorporated in the building                 
installation wiring”.
The disconnect device, fuse spur, should be a two-pole type and 
have contact separation of no less than 3mm.
The fuse in the spur should be 3A.

Mains Cable

The 250mA & 2.5A PSU uses 0.75mm

2

 H05VV-F type cable.

Equipment with a non-detachable power supply cord (namely 
the current 250mA PSU) the cable should have a minimum        
designation type not less than H03VV-F or H03VVH2-F.

Equipment with a detachable power supply cord (namely the 
current 2.5A PSU) should have a minimum designation type not 
less than H03VV-F or H03VVH2-F

For both PSU’s (input mains current less than 3A) the minimum 
conductor size is 0.75mm

2 

or 18 AWG.

If stranded wire is to be supplied for connecting the PSU to the 
mains supply it cannot be soft soldered.

Содержание RapidView
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды