manualshive.com logo in svg

ADEMCO VIDEO RapidView, Руководство по эксплуатации

Поделиться
Скачать
ADEMCO VIDEO RapidView Скачать руководство пользователя страница 15

Rapid View                                                                                              Operation Guide

Page 9                                                     © Ademco Video 2002 MNRDVO250602US

Chapter 3

3.Presets and Tours

1.0

To Define a Preset

For example, to define Preset 1.

Move the selected camera to view the desired preset position, using 
the joystick, zoom, focus and iris buttons.

Press and hold the ‘PRESET’ button.

Press button ‘1’.

Release the ‘PRESET’ button.

The current position of the camera has now been defined as Preset 1.

Up to 128 presets can be defined, and these are numbered 0 - 127.

2.0

To Seek a Preset

For Example, to seek Preset 1.

Press button ‘1’.
Press the ‘PRESET’ button.

The camera will now move at the maximum speed to the previously 
defined Preset 1.

The user may also select presets 1 - 4 by single button presses, using 
the buttons labelled ’PRESET 1’ to ‘PRESET 4’.

3.0

To Start a Tour of Presets

The units in the RapidView range have enough memory for four             
different tours. After programming the tours, as detailed in the next 
sections, they may be recalled in the following way.

Press the number button that corresponds to the tour       
number, either ‘1’, ‘2’, ‘3’, or      ‘4’.
Press the ‘AUTOPAN’ button.

Содержание RapidView
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды