manualshive.com logo in svg

ADEMCO VIDEO RapidView, Руководство по эксплуатации

Поделиться
Скачать
ADEMCO VIDEO RapidView Скачать руководство пользователя страница 18

Operation Guide                                                                                              Rapid View

© Ademco Video 2002 MNRDVO250602US                                                    Page 12

Chapter 3

Press button ‘1’, then press button ‘4’, then press the ‘TIME’   
button. (This defines a 14 second dwell time at this preset             
position.)
Release the ‘AUTOPAN’ button.

The tour is now set up. To operate ‘Tour 3’

Press button ‘3’, then press the ‘AUTOPAN’ button.

Note:

The range of the dwell times that can be set varies 
from 1 to 254 seconds. Entering a time of ‘0’ will     
select 1 second dwell time.

7.0

To Stop a Tour of Presets

Press the ‘AUTOPAN’ button. (This will turn off the tour.)

The tour will also stop if the telemetry buttons or the joystick are used 
to control the camera.

8.0

To Restart a Tour of Presets

Press the ‘AUTOPAN’ button. (This will start the last tour that the 
RapidView was carrying out.)

Note:

If an alarm is activated on a camera whilst the       
keyboard is being used to program a tour for that 
camera, the programming will be interrupted at the 
point of activation. (The tour will also require           
re-programming.)

Содержание RapidView
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды