manualshive.com logo in svg

ADEMCO VIDEO RapidView, Руководство по эксплуатации

Поделиться
Скачать
ADEMCO VIDEO RapidView Скачать руководство пользователя страница 46

Operation Guide                                                                                              Rapid View

© Ademco Video 2002 MNRDVO250602US                                                    Page 40

Chapter 5

house. Once we have defined our Privacy Zone we can then pan, tilt 
and zoom safe in the knowledge that the area under our Privacy Zone 
will not become visible.  The area under the Privacy Zone will be         
increased from the actual size of the preset so that it can never be         
displayed.

The Privacy Zone covers a greater area than the object that it covers, 
this is to make sure that there is no chance of the area under the Privacy 
Zone becoming visible.  You can make this ‘safety region’ smaller by 
zooming into the object  more than ncessary.

Figure xiv   

Defining a Preset for a ‘Privacy Zone’

Note:

The objects benearth the shaded area will NOT be 
shown.

Zoomed
    in

Zoomed
    out

a) Before defining                                 b) Privacy Zone is                                  c) Privacy Zone
    Privacy Zone                                        defined                                                    after being defined

Содержание RapidView
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды