manualshive.com logo in svg

ADEMCO VIDEO RapidView, Руководство по эксплуатации

Поделиться
Скачать
ADEMCO VIDEO RapidView Скачать руководство пользователя страница 14

Operation Guide                                                                                              Rapid View

© Ademco Video 2002 MNRDVO250602US                                                    Page 8

Chapter 2

FOR WASH.
Press and hold the ‘WASH’ button to activate the washer.
Release the ‘WASH’ button to turn off the washer.

Note:

If the LED above the ‘WASH’ button is illuminated, 
the washer is ON.

If the receiver has a separate momentary function (auxiliary), it is      
controlled as follows:

Press the ‘0’ button, then press and hold the ‘AUX’ button to activate 
the auxiliary function.

Release the ‘AUX’ button to turn off the auxiliary function.

Note:

The LED above the ‘AUX’ button is not altered by 
this operation as it is used to monitor ‘Change Over’ 
Orbiter Microspheres.

Note:

The ‘#’ button has no function on the Rapid View.

Содержание RapidView
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды