ADB Safegate IDM 8000 Скачать руководство пользователя страница 87

Страница: 87 / 118

U2 output voltage / Byte 8

The value is always 0-125 in which 125 is the maximum output voltage of the CCR which again depends on the CCR size. This means that

the PLC (or the PC) must have the CCR size as a parameter in order to display the actual U2. One digit is CCR size (VA) / 6.6A / 125.

P2 output actual power / Byte 9

The value is always 0-125 in which 125 is the maximum power of the CCR which again depends on the CCR size. This means that the PLC (or

the PC) must use the CCR size parameter when displaying the actual P2- reading. One digit means CCR size (W) / 125

CCR type and size parameters / Byte 11

This byte indicates the CCRs type and size to control system and can be used to automatically update these parameters in the control

system.

Three first bits (80-82, Lsb=80) define the CCR type in binary coded format: 0=normal CCR, 1=direction changer, 2-6= 2-6 circuit selectors

(Dec values)

Four last bits (84-87, Lsb=84) define the CCR size in binary coded format: 1=2,5kVA, 2=3kVA, 3=4kVA, 4=5kVA, 5=7,5kVA, 6=10kVA,

7=12,5kVA, 8=15kVA, 9=17,5kVA, 10=20kVA, 11=25kVA and 12=30kVA (Dec values).

Redundant duplicated interface / other interface control bit status / Byte 12

This information is provided for the control system to facilitate control channel / interface monitoring.

Displays which can be calculated from the above values in the control system

- S2 = I2 * U2 = Apparent power taken by the load

-Pf2 = P2 / S2 = load power factor, how inductive the load is ( lamp faults etc)

UM_IDM-8000, Rev. 1.7, 2021/05/06

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды