ADB Safegate IDM 8000 Скачать руководство пользователя страница 46

Страница: 46 / 118

4.5.2 Over Current Protection

This function protects the lamps in the AFL circuit and also the CCR from long term over current caused by possible

regulation/component fault of the CCR. If the output current exceeds the threshold level for a predefined time period (delay

time), the CCR trips. Two levels A (normally higher threshold and shorter delay) and B are provided. Local or local+remote

reset modes can be selected.

Header / function

Data 1

Data 2

Fact set

Allowed range

Over current prot

Threshold level A

Level A

7.20A

3.30-7.75A in 0.05A steps

Threshold level B

Level B

6.90A

3.30-7.75A in 0.05A steps

Delay time A (s)

Delay A

0.1-10s in 0.1s steps

Delay time B (s)

Delay B

0.1-10s in 0.1s steps

Reset mode abbrev.

Reset m.

L / L+R

Setting sequence

1. Go to over current protection by selecting Set/Prot/Ocu.

1. If necessary adjust levels A, B with + - , select Set and then select Next.

1. If necessary adjust delay times A, B as in step 2.

1. If necessary adjust the reset mode (L or L+R) as in step 2.

Operational test

Adjust the threshold level below the actual output current value and make sure that the CCR trips in due time.

4.5.3 Over Current Protection, Fast Reset

The function protects the lamps in the AFL circuit and also the CCR for fast over currents, caused by load changes. If the

output current exceeds 125% of nominal maximum intensity, the CCR will disable the output within 10ms for at least 40 ms,

and restores operation to normal. If this fast reset repeats immediately within one second, after 5 fast resets the CCR will trip

to protect the AFL circuit.

4.5.4 Input Voltage Protection

This function protects the lamps in the AFL circuit and also the CCR from possible regulation/component fault of the CCR

caused by long term over/under input voltage.
If the input voltage is out of acceptable limits (L a + = +15% and L a - = -20%, deviation automatically set from the nominal

value) for a predefined delay time the CCR trips. CCR starts automatically after the input voltage returns to acceptable limits.

Function

Limit type

Value

Trip value

Return value

Input voltage protection

Threshold level A +

Threshold level A –

+15%

264 / 460 Vac

253 / 440 Vac

-20%

184 / 320 Vac

196 / 340 Vac

IDM 8000
User Interface

34
Copyright

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды