ADB Safegate IDM 8000 Скачать руководство пользователя страница 56

Страница: 56 / 118

SET SYSTEM HW SETTING

Step

Task

Remarks

Turn IDM 8000 main switch off

Remove MCU unit

Set SW1 disp switches to desired positions

Insert MCU and turn the main switch on

The settings can be viewed for checking from the display:

VIEW SYSTEM HW SETTING

Step

Task

Buttons

To open view/system select

View/More/More/Sys

Scroll displays until “DIP POS” is on Data field 2

Next.

SYSTEM HW SETTING DISPLAYS

See the column “view-value” in the “HW-settings” table to interpret the display values.

Header / function

Data 1

Data 2

Factory setting

Allowed range

System information

DIP POS

ABCD where

Project

A = U1 Nominal value code

0-3

B = F1 Nominal value code

0-1

C = Type code

0-7

D = Remote control code

0-3

4.6.8 System settings

General CCR settings are only enabled when the control switch is in Off-position.

Note

: ERR indication is provided if settings are not accepted.

•

CCR size: is used for output voltage calibration and scaling size dependent measurement data for remote monitoring.

•

CCR type: display only, normally set from HW-system settings. Can be set only if dip switch code enables setting from

display.

•

M-switch defines if the maintenance switch is used for earth fault maintenance or Lamp fault B reset (FAA-monitor reset)

function or is not used at all.

•

Monitor defines the indication operation mode. Realtime warnings and alarms are indicated only when the CCR is in

operation and the measurement is active. Latching: alarms and warnings are indicated after the alarm has been activated

even when the CCR has been in off state.

•

Password defines if the settings can be altered with or without asked password. Password is required with setting ON.

Factory setting is Off (No password needed). Factory setting of default password is 547.

•

No of lamps is used in lamp fault % indication and is provided for 2 directions.

•

Lamp rating; used only for information purposes, pre-set selections, provided for 2 directions.

IDM 8000
User Interface

44
Copyright

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды