ADB Safegate IDM 8000 Скачать руководство пользователя страница 45

Страница: 45 / 118

Reset mode

Defines in which way the operated protection can be reset i.e. the CCR can be started again:

•

L = Local reset, protection resets only by controlling the CCR off from the local operation switch of the CCR after which the CCR can be

restarted.

•

L+R = Local+remote reset, protection is reset by controlling the CCR off either locally or via remote control. Maintenance personnel do

not need to visit the CCR station for a CCR restart.

•

A = Automatic reset: protection resets automatically when the actual value returns within the acceptable limits (normally level A +

hysteresis). No selection, used with U1, f and T protections.

4.5.1 Open Circuit Protection

This function protects the maintenance personnel in case of open circuit by tripping the CCR after a delay time if the output

current stays below a predefined threshold level. The output current must exceed the threshold level to enable CCR normal

operation. Local or Local+remote reset modes can be selected. The capacitive current monitor may be selected to monitor

the power factor of the load. With an open circuit on long shielded cables, there may be enough capacitance in the cable to

hold the output current above the open circuit threshold level. If the load power factor is highly capacitive, the capacitive

output current monitor will switch off the CCR when selected and indicate an open circuit. Detection time for capacitive

output current is one second.

Header / function

Data 1

Data 2

Fact set

Allowed range

Open circuit prot

Threshold level

Level

1.5A

0-6.60A in 0.05 steps

Delay time

Delay

0,5s

0.1-10s in 0.1s steps

Reset mode abbrev.

Reset m.

L / L+R

Op. mode for capacitive current monitor

CAP MON

Off

Off / ON

Setting sequence

1. Go to open circuit protection display by selecting Set /Prot /Ocs.

1. If necessary adjust threshold level with + - buttons and select Set, then select Next.

1. If necessary adjust delay time as in step 2.

1. If necessary adjust the reset mode (L or L+R) with + - buttons.

1. If necessary select the capacitive current monitor operation.

Operational test

Two ways can be used to test the operation of the protection:

•

Real test: Open the AFL-circuit and start the CCR. Make sure that the CCR trips in due time.

Warning! High voltage circuit! Adequate insulation and distances must be maintained during test.

•

Simulated test: Adjust the threshold level above the actual output current level and check that the CCR trips in due time.

UM_IDM-8000, Rev. 1.7, 2021/05/06

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды