ADB Safegate IDM 8000 Скачать руководство пользователя страница 79

Страница: 79 / 118

Appendix B: Appendix B – Serial communication interface –

Modbus TCP connection

Cabling

Each communication interface has its own

standard Ethernet connection cable which is

connected (plug in) between the control system

Ethernet switch (hub) and the CCR.

Connector

RJ45 female connector is provided on the card

front plate.

Termination

No termination is required

Addressing

Each communication interface must have unique

address on the Ethernet local area network where

it is connected (including control system devices

and CCR communication interfaces).

•

IP address =192.168.0.n (default)

The last field n is binary coded with 8 dip-switches

on the front plate of the communication interface.

Note : Addresses 0 and 127 cannot be used.

•

Subnet mask = 255.255.255.0 (default)

•

Default gateway = 0.0.0.0 (default, no gateway

set)

•

It is possible to change the default IP address

192.168.0 (IAONA standard for private

networks), the subnet mask and default

gateway address if necessary by performing

the following steps.

•

Connect a PC directly to the RJ45 female

connector on the CCR.

•

Open a web browser and type the IP address

of the CCR into the address field.

•

The following screen will appear.

•

Type the new network information in the

relevant fields.

•

Store the configuration.

•

Turn off the power to the CCR.

•

Set the dip-switch on the CCR to address 0.

•

Turn on the power to the CCR.

•

Test that the new IP address is valid.

•

Note: Only the last digit of the default IP

address 192.168.0.n can be set using the dip-

switch. If the default IP address has been

changed the dip-switch must remain set to

address 0.

UM_IDM-8000, Rev. 1.7, 2021/05/06

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды