ADB Safegate IDM 8000 Скачать руководство пользователя страница 40

Страница: 40 / 118

I2 calibration

1. Connect external calibrated RMS A-meter (10A, accuracy better than 1%) in series with the load circuit. Use at least 10% load of the CCR

capacity.

Warning!

High voltage circuit – De-energize CCR before connecting!

Note : For more information on easy meter connection, see

Series Cut Out (SCO) option

in Appendix M – Ouput Terminals. Clamp meter

accuracy is normally not adequate for 1% accuracy. For periodic maintenance checks, clamp type meter is still recommended for safety reasons.

1. Select the second highest current step (approx. 5A).

1. Go to I2/U2 calibration: select Set/Cal/Out.

1. Adjust the I2 reading on datafield 1 to equal with the external meter reading.

1. Make sure that the readings are equal then select Set.

Warning!

Make sure that there is max 10% deviation between the two readings. Selecting set

with bigger difference between the readings may result to over current on the output

circuit!

1. Check that both readings are equal, if necessary repeat steps 4-6.

Note : I2 calibration affects also to VA-drop function.

Calibration with short circuit load (U2 = 0) is not allowed.

Calibration of more than ±10% from factory defaults is not allowed -> ERR indication in display.

U2 calibration

1. Connect external calibrated RMS V-meter (Min 30V, accuracy better than 1%) to the voltage transformer test

outputs located on the right side of the power unit of the control rack.

1. Select the maximum current step (6.6A).

1. Go to I2/U2 calibration: select Set/Cal/Out and then Next.

1. Check the external meter reading and adjust the U2 reading on data 1 to be equal with the external meter reading and then select Set .

Note : Round up to next bigger value e.g. 20.12->20.2.

1. Make sure that the both readings are equal and if necessary repeat step 4.

Note : U2 calibration affects also to VA-drop function

Calibration of more than ±10% from factory defaults is not allowed -> ERR indication in display.

4.4.2 Input Voltage U1 Calibration

Header / function

Data 1

Data 2

Remarks

U1 calibration

U1 / V

U1 Cal

+ - adjust

IDM 8000
User Interface

28
Copyright

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды