ADB Safegate IDM 8000 Скачать руководство пользователя страница 13

Страница: 13 / 118

1.0 Safety

Introduction to Safety

This section contains general safety instructions for installing and using ADB SAFEGATE equipment. Some safety instructions

may not apply to the equipment in this manual. Task- and equipment-specific warnings are included in other sections of this

manual where appropriate.

1.1 Safety Messages

HAZARD Icons used in the manual

For all HAZARD symbols in use, see the Safety section. All symbols must comply with ISO and ANSI standards.
Carefully read and observe all safety instructions in this manual, which alert you to safety hazards and conditions that may

result in personal injury, death or property and equipment damage and are accompanied by the symbol shown below.

WARNING

Failure to observe a warning may result in personal injury, death or equipment damage.

DANGER - Risk of electrical shock or ARC FLASH

Disconnect equipment from line voltage. Failure to observe this warning may result in personal injury, death, or

equipment damage. ARC Flash may cause blindness, severe burns or death.

WARNING - Wear personal protective equipment

Failure to observe may result in serious injury.

WARNING - Do not touch

Failure to observe this warning may result in personal injury, death, or equipment damage.

CAUTION

Failure to observe a caution may result in equipment damage.

Qualified Personnel

Important Information

The term qualified personnel is defined here as individuals who thoroughly understand the equipment and its safe

operation, maintenance and repair. Qualified personnel are physically capable of performing the required tasks, familiar

with all relevant safety rules and regulations and have been trained to safely install, operate, maintain and repair the

equipment. It is the responsibility of the company operating this equipment to ensure that its personnel meet these

requirements.

Always use required personal protective equipment (PPE) and follow safe electrical work practice.

UM_IDM-8000, Rev. 1.7, 2021/05/06

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды