ADB Safegate IDM 8000 Скачать руководство пользователя страница 48

Страница: 48 / 118

B-levels are used as warning indication and can be set by the user. Temperature function protects the CCR from overheating

caused by e.g. too high environmental temperature. If the thyristor cooling element temperature exceeds Level A value the

CCR trips. Level B is used as warning and can be set by the user. Reset mode is always A (resets automatically when actual

value returns within acceptable limits) for both protections.

Header / function

Data 1

Data 2

Fact set

Allowed range

Freq. and temp prot

Nominal value

Nom

Project*

HW setting w.dip switch *

Threshold level B +

F b (+)

Project*

Nom - F a + in 1Hz steps**

Threshold level B –

F b (-)

Project*

Nom - F a - in 1Hz steps

Delay time

F delay

0.1-10s in 0.1s steps

Temp thresh. Level

T L

+ 80 C

0-95 C in 1 C steps

BTemp delay time

T Delay

10s

0.1-10s in 0.1s steps

* Can be set from display but dipswitch settings overruns it at power up

** F a, + and F a, - automatically derived from nominal value

Setting sequence

1. Go to freq/temp protection by selecting Set/Prot /F/T .

1. If necessary adjust freq nominal value with , + / - , select Set and then select Next.

1. If necessary adjust threshold levels F b, + and F b, - as in step 2.

1. If necessary adjust frequency protection delay time, as in step 2.

1. If necessary adjust temperature level T b, as in step 2.

1. If necessary adjust temperature protection delay time, as in step 2.

Operational test

Adjust the frequency nom value to be 10Hz out of real nominal value and make sure that the protection operates in due time.

Warnings can be tested by adjusting the warning level.

IDM 8000
User Interface

36
Copyright

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды