ADB Safegate IDM 8000 Скачать руководство пользователя страница 77

Страница: 77 / 118

Appendix A: Appendix A – Serial communication interface –

Profibus DP connection

Bus cabling

The bus cabling is made in daisy chain form (from the first unit to second … to last) Special Profibus DP cable must be used. Two wires (+

and -) are connected in each fieldbus connector.

Warning!

Make sure that the polarity is not mixed anywhere on the bus.

Bus connectors

D9 female connector provided on the card front plate. Special Profibus DP fieldbus connectors

must be used. The connectors normally include 2 screw terminals for incoming and outgoing

cable connection and may include also bus termination switches.

Bus termination

Profibus DP bus should be terminated from the both ends of the bus (i.e. the 1

and Last units).

Termination can be done in following ways:

1. Active terminators with guaranteed power supply are recommended to use (protects against

power loss of a CCR at the end of the bus).

2. If active terminators are not available use the terminators in the fieldbus connectors

(disconnecting the connector will not affect the bus status)

3. As last a resort use the termination switches on the fieldbus cards.

WaRning!

Make sure that there is no double termination i.e. if

use active or connector termination, Make sure that

the other termination switches are off.

Addressing

Each fieldbus card (i.e. node) must have unique address which is set as a sum of two rotary switch

settings x10’ and x1’ (from 0 to 99).

Status led information

Led no.

Description

Colour

Off

Blink 1Hz

Blink 2hz

Blink 4hz

Not used

UM_IDM-8000, Rev. 1.7, 2021/05/06

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды