ADB Safegate IDM 8000 Скачать руководство пользователя страница 69

Страница: 69 / 118

4a.

Clear operating time counters

2.3 View functions

System settings:

Set the CCR size (

Note: If size = 0, calibrations and settings reset to factory defaults

after power break).

Check the type of the CCR if set with motherboard switches.

Set maintenance switch operation mode No / Efm / Lf1

Select password use.

Set the circuit data, number of lamps and power of the transformers.

Set the circuit id. If the CCR number is set to 0, main display shows output current and –

voltage instead of circuit info.

Set the lamp life monitoring parameter

Set service date.

2.6.8 System settings

Check and set the time and date.

2.6.6 Time and Date settings

4b.

Settings for the remote control

•

Serial interface, Settings Rcs

Check the identification of the card (Serial)

Check the type of the card (Profibus)

Check the number of identified cards (01 / 02)

Set the failsafe mode Cont/ FS/ Fsoff/ ContHB/ FS HB/ Fsoff HB

Set the failsafe step 00-07

2.6.9 Remote control settings

•

Parallel interface, settings Rcs

Check the identification of the card (Parallel)

Set control coding Dec / Bin

Set control mode Cont / Imp

Set grouping mode for common fault SumF / SysF

2.6.9 Remote control settings

Start the CCR with local control. Check all current steps and adjust if needed.

2.6.1 Output current step setting

Switch the CCR off and connect the output terminals to operating mode “I2 cal”. Use RMS

ammeter with accuracy of 1% or better.

1.3.4 High voltage circuit

Check input voltage calibration.

2.4.2 Input voltage U1 calibration

Check output current calibration.

Check output voltage calibration.

2.4.1 Output current I2 and voltage

U2 calibration

Check the tapping info (System info)

Adjust load matching if needed (tapping)

3.4 Load matching

If the CCR has a circuit selector installed, set the CS min current

2.6.10 Circuit selector minimum

current setting

Run all intensity steps and check that the input voltage is sufficient.

8..

Check and adjust/test (if desired) the supply voltage protection

2.5.4 Input voltage protection

Check and adjust/test (if desired) the input frequency protection

Check and adjust/test (if desired) the temperature protection

2.5.5 Input frequency and

temperature protection

Check and adjust/test (if desired) the open circuit protection

2.5.1 Open circuit protection

Check and adjust/test (if desired) over current protection

2.5.2 Over current protection

Test MCU card leds

2.3 View functions

UM_IDM-8000, Rev. 1.7, 2021/05/06

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды