manualshive.com logo in svg

Adaptec 2100S - SCSI RAID Controller, Руководство по установке, Страница: 98 / 100

Поделиться
Скачать
Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 98

D-3

Controller Reset Procedures

4

When you see the Adaptec splash screen, click 

Create Driver 

Disk

. Then, click the appropriate menu option.

5

Insert a floppy disk and click 

OK

. The system creates the 

bootable SMOR disk.

6

Remove the 

Adaptec RAID Installation CD 

and the driver floppy 

disk.

7

Shut down the system.

8

If necessary, reinstall the controller in your system.

Now, to reset the controller firmware, BIOS, and SMOR, perform the 
following tasks:

1

Install a jumper on flash mode 0 jumper connector. For the 
location of the jumper connector, refer to 

Appendix A

. 

2

Insert the SMOR boot disk and boot the system. SMOR starts.

3

Use SMOR to flash the controller firmware.

4

Shut down the system.

5

Remove the jumper you installed in 

Step 1

.

6

Remove the SMOR boot disk.

7

Reboot the system from the SMOR boot disk. If the system 
restarts normally, the controller can now be configured using 
SMOR or Storage Manager. 

8

Use SMOR to flash the controller BIOS and SMOR images.

If the system fails to restart, call Adaptec Technical Support.

Содержание 2100S - SCSI RAID Controller





































































































Отзывы:

Нет отзывов