Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 25

Страница: 25 / 100

2-1

Installing Your Controller

In this Chapter

Configuring ATA Drives

When configuring drives for the Adaptec 2400A, you need to

■

Select and configure compatible drives..

■

Attach supplied ATA cables.

ATA Drives

Your Adaptec 2400A controller supports ATA/66 and ATA/100
hard drives only. Use ATA/100 cables only.

RAID drives should be as alike as possible in terms of capacity and
performance. Set the drives to operate as a master (factory default).
If previously used, format the drive according to manufacturer’s
recommendations.

➤

Configuring ATA Drives

2-1

➤

Configuring SCSI Devices

2-2

➤

Installing Additional Cache Memory

2-6

➤

Installing the Battery Backup Module

2-8

➤

Installing the Controller

2-8

➤

Using SMOR

2-10

Содержание 2100S - SCSI RAID Controller





































































































Результаты поиска

Содержание 2100S - SCSI RAID Controller

Отзывы:

Adaptec 2100S - SCSI RAID Controller, Руководство по установке, Страница: 25 / 100

Результаты поиска

Содержание 2100S - SCSI RAID Controller

Отзывы: