Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 69

Страница: 69 / 100

4-2

Adaptec RAID Installation Guide

System Requirements

You need a system that meets the following minimum hardware
requirements:

■

Pentium or equivalent CPU that is at least as fast as 200 MHz

■

64 MB of RAM (128 MB of RAM for NetWare)

■

60 MB of disk space for Storage Manager Pro. The software
occupies 20 MB, and uses an additional 40 MB during
installation

■

Mouse or other pointing device

■

CD drive

■

TCP/IP stack

■

Graphics card and monitor capable of 800

600 resolution and

256 colors

Note:

Storage Manager for UNIX Motif displays colors

correctly only if your video display adapter is set to display
256 colors.

Installing Storage Manager Pro

Operating System Compatibility

Storage Manager Pro runs on the following operating systems:

■

Microsoft Windows 2000, Windows NT 4.0, and Windows 95/98
(see

page 4-3

)

■

Novell NetWare 4.

and 5.

(see

page 4-4

)

■

FreeBSD (see

page 4-7

)

■

Red Hat Linux 6.

and 7.0 (see

page 4-7

)

Storage Manager Pro’s remote management capabilities are only
available on your system if it contains a network card configured to
use the TCP/IP protocol.

Содержание 2100S - SCSI RAID Controller





































































































Результаты поиска

Содержание 2100S - SCSI RAID Controller

Отзывы:

Adaptec 2100S - SCSI RAID Controller, Руководство по установке, Страница: 69 / 100

Результаты поиска

Содержание 2100S - SCSI RAID Controller

Отзывы: