Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 100

Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 10

1-2

Adaptec RAID Installation Guide

Read this First

Before you begin installing your new Adaptec RAID controller, read
this chapter. This chapter is an important guide to the rest of the
documentation and provides a summary of the installation process.

System Requirements

The following system requirements are discussed:

■

Storage requirements for drivers and software

■

Motherboard compatibility

■

ATA requirements –

Adaptec 2400A only

■

SCSI requirements –

Adaptec 2100S/3200S/3210S/3400S/3410S only

Storage Requirements for Drivers and Software

Adaptec Storage Management software and device drivers require
approximately 4 MB of disk space. The host system should have
64 MB of memory, and a Pentium processor that is at least as fast as
200 MHz. A mouse and SVGA color monitor are also required.

Adaptec Storage Manager Pro requires 40 MB of available disk space
for installation. The host system should have 64 MB of memory, a
Pentium processor (200 MHz or faster), and a video adapter capable
of 800

×

600 resolution with 256 colors.

«
...
8
9
10
11
12
...
»

Содержание 2100S - SCSI RAID Controller





































































































Отзывы:

Нет отзывов