Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 6

Страница: 6 / 100

Adaptec RAID Installation Guide

Installing Additional Cache Memory 2-6

Seating the Module –

Adaptec 3200S/3400S Only 2-6

Seating the Module –

Adaptec 2400A/2100S/3210S/3410S

Only 2-7

Finishing up – All Models 2-7

Installing the Battery Backup Module

2-8

Installing the Controller 2-8

Determining the Booting Controller 2-9
Controller IRQ and Address 2-9

Using SMOR 2-10

Installing the Driver

Windows 2000 3-2

Installing the Driver in a New System 3-2
Adding the Controller to an Existing System 3-3
Upgrading Windows NT to Windows 2000 3-4

Windows NT 4.0 3-5

Installing the Driver in a New System with Only One

Controller 3-6

Installing the Driver in a New System with Other

Hardware 3-7

Upgrading the Controller in an Existing System 3-8
Changing the Driver in an Existing System 3-9

Windows 95, Windows 98, and Windows Me 3-11

Installing the Driver in a New Windows 98/Me

System 3-12

Installing the Driver in a New System with Windows 95

(OEM SR2 – Version 95B) 3-14

Adding the Controller to an Existing Windows 95/98/

Me System 3-16

Upgrading Windows 95 to Windows 98/Me (Upgrade

Version) 3-18

Novell NetWare 3-18

Installing the Driver for a Boot Controller in a New

NetWare 4.11 Server 3-19

Installing the Driver in a Existing NetWare 4.11

Server 3-20

Содержание 2100S - SCSI RAID Controller





































































































Результаты поиска

Содержание 2100S - SCSI RAID Controller

Отзывы:

Adaptec 2100S - SCSI RAID Controller, Руководство по установке, Страница: 6 / 100

Результаты поиска

Содержание 2100S - SCSI RAID Controller

Отзывы: