manualshive.com logo in svg

Adaptec 2100S - SCSI RAID Controller, Руководство по установке, Страница: 54 / 100

Поделиться
Скачать
Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 54

3-19

Installing the Driver

Installing the Driver for a Boot Controller in a New 
NetWare 4.11 Server

In this scenario, you are installing an Adaptec RAID controller as a 
boot controller in a new NetWare 4.11 server with other hardware.

Note: 

Part of this procedure requires that you have enough 

free space on your 

C

 drive to hold the contents of the 

NetWare CD.

To install the driver

1

Create a driver floppy disk using the 

Adaptec RAID Installation CD

. 

To create the disk

a

Insert the 

Adaptec RAID Installation CD

 in your drive and a 

blank floppy disk in the floppy disk drive.

b

Copy all the files in 

\packages\netware\4.11\driver

 to the 

floppy disk.

c

Remove the 

Adaptec RAID Installation CD

 and the driver 

floppy disk.

2

Install and configure your Adaptec RAID controller and hard 
drives according to the instructions in 

Chapter 2

. Verify that 

the Adaptec RAID controller is the primary controller. If other 
controllers are present, install the Adaptec RAID boot 
controller in a lower-numbered PCI slot than the other 
controllers.

3

Install and configure a secondary controller, if any.

4

Start up the server. During restart, press 

Ctrl+A

 to start SMOR. 

Use SMOR to create the RAID. For details, refer to 

Using 

SMOR

 on page 2-10

.

5

Create a 750-MB DOS partition on the Logical Storage Unit 
(LSU), which can be a drive or array group, with the lowest 
LSU ID.

6

Boot the server to DOS from the partition you created in 

Step 5

. 

Verify that you load the required CD drivers.

7

Insert the NetWare 4.11 CD. 

Содержание 2100S - SCSI RAID Controller





































































































Отзывы:

Нет отзывов