manualshive.com logo in svg

Adaptec 2100S - SCSI RAID Controller, Руководство по установке, Страница: 45 / 100

Поделиться
Скачать
Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 45

3-10

Adaptec RAID Installation Guide

d

When you see the Adaptec splash screen, click 

Create 

Driver Disk

. Then, click the appropriate operating system.

e

Insert a floppy disk and click 

OK

. The system creates the 

driver disk.

2

Shut down the system and remove the 

Adaptec RAID 

Installation CD

 and the driver floppy disk.

3

Restart the system and open the Control Panel. Click the 

SCSI 

Adapters

 icon. Then select the 

Drivers

 tab and click 

Add

.

4

Insert the driver disk you created in 

Step 1

 and then click

 Have 

Disk

.

5

Select 

Adaptec I

2

O RAID Host Adapter Driver for NT 4.0

.

6

After the driver is loaded, shut down the system. 

7

Install and configure the Adaptec RAID controller and hard 
drives according to the instructions in 

Chapter 2

. Leave the 

existing controller installed.

8

Start up the system.

Содержание 2100S - SCSI RAID Controller





































































































Отзывы:

Нет отзывов