manualshive.com logo in svg

Adaptec 2100S - SCSI RAID Controller, Руководство по установке, Страница: 14 / 100

Поделиться
Скачать
Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 14

1-6

Adaptec RAID Installation Guide

About the Documentation

The complete documentation set for Adaptec RAID controllers 
consists of the following:

■

Adaptec RAID Installation Guide 

(this book)—Contains 

information that helps you to configure and install your 
Adaptec RAID controller and attached devices.

■

Adaptec

 

Storage Manager Pro User’s Guide—

Describes how to 

use the Storage Manager Pro application to manage your 
controller and storage subsystem. 

■

Adaptec Adaptec Storage Management Software User’s Guide—

Describes how to use SMOR, Adaptec Storage Manager 
software, and the RAIDUTIL command line utility. 

Both

 Storage Manager Pro 

and

 Storage Manager

 provide online help 

for creating and managing RAIDs, including topical and pop-up 
help displays. The 

User’s Guides

 for both applications are included 

on the 

Adaptec RAID Installation CD

. Refer to 

page 1-9

 for details.

Using the Adaptec RAID Installation CD

The 

Adaptec RAID Installation CD

 contains the RAID Management 

Software, device drivers, and user documentation needed to install 
and support your Adaptec RAID Controller. 

3

SCSI RAID controllers support Ultra160 and legacy hard drives and non-hard-
drive devices, such as CD and tape drives.

4

Adaptec RAID software supports up to 

64

 hard drives per array and up to 

2 Terabytes of storage capacity.

5

VHDCI (Very High Density Connector Interface).

6

Requires a special hot-swap carrier.

7

Indicates when activity has occurred that may require operator attention.

Содержание 2100S - SCSI RAID Controller





































































































Отзывы:

Нет отзывов