manualshive.com logo in svg

Adaptec 2100S - SCSI RAID Controller, Руководство по установке, Страница: 55 / 100

Поделиться
Скачать
Adaptec 2100S - SCSI RAID Controller Скачать руководство пользователя страница 55

3-20

Adaptec RAID Installation Guide

8

Insert the driver disk you created in 

Step 1

 and run 

dpt411.bat

. 

This utility copies the necessary files to the

 

C

 

drive.

9

Run 

install.bat

 from the 

C

 drive.

10

When asked to select a disk driver select 

i2opci.nlm

. Enter the 

slot number where the controller is installed and press 

F10

.

11

Select 

Save parameters and load driver

.

12

Select 

Yes

 to select another driver.

13

Select 

bkstrosm.ham

. Enter the slot number where the 

controller is installed and press 

F10

.

14

Select 

Save parameters and load driver

.

15

Install any additional drivers and continue the installation.

16

Select 

Edit startup.ncf

. If needed, edit the file so that 

i2opci.nlm

 

is listed before 

bkstrosm.ham

 in your 

startup.ncf

 file.

17

Continue with the NetWare installation according to the 
Novell documentation. 

18

Upgrade your NetWare version to the minimum patch level 
specified by Novell. 

Installing the Driver in a Existing NetWare 4.11 Server

In this scenario, you are integrating an Adaptec RAID controller into 
an existing NetWare 4.11 server as a secondary controller. To install 
the driver

1

Upgrade your existing NetWare server to the minimum patch 
level specified by Novell.

2

Create a driver floppy disk using the 

Adaptec RAID Installation CD

. 

To create the disk

a

Insert the 

Adaptec RAID Installation CD

 in your drive and a 

blank floppy disk in the floppy disk drive.

b

Copy all the files in 

\packages\netware\4.11\driver

 to the 

floppy disk.

c

Remove the 

Adaptec RAID Installation CD

 and the driver 

floppy disk.

Содержание 2100S - SCSI RAID Controller





































































































Отзывы:

Нет отзывов