Abbott i-STAT 1 Скачать руководство пользователя страница 478 | Manualshive

Страница: 478 / 658

background image

Celite ACT - 2

Art: 714185-00N

Rev. Date: 30-Jan-12

Contents
Each i-STAT

Celite

ACT cartridge provides a sample collection chamber, sensors to detect the coagulation

endpoint, and dry reagents necessary to initiate and allow coagulation. Stabilizers and reagents are coated
on a section of the sensor channel and include the following reactive ingredients:

Reactive Ingredient

Diatomaceous Earth

Thrombin Substrate

Metrological Traceability
The i-STAT System test for Celite Activated Clotting Time measures the time interval required for complete
activation, by Celite

®

, of the coagulation cascade in arterial or venous whole blood (dimension seconds) for

in vitro

monitoring of moderate- and high-level heparin therapy. Presently, no international conventional

reference measurement procedure or international conventional calibrator for

Celite

ACT is available.

Celite

ACT values assigned to i-STAT’s controls are traceable to i-STAT’s selected reference measurement

procedure, which employs diatomaceous earth (Celite) activated glass reagent tubes, an automated timer
and traditional viscometric clot detection and is run under specified temperature and sample conditions.
i-STAT System controls are validated for use only with the i-STAT System and assigned values may not be
commutable with other methods. Further information regarding metrological traceability is available from
Abbott Point of Care Inc..

Expected Values

Test/Abbreviation

Units

Reportable Range

Reference Range

(PREWRM)

Reference Range

(NONWRM)

Activated Clotting

Time/ACT

seconds

50 - 1000*

74 - 125

84 - 139

*

The range from 80 - 1000 seconds has been verified through method comparison studies.

Clinical Significance
The ACT is primarily used to monitor a patient’s state of anticoagulation due to heparin that is administered
during a medical or surgical procedure. It is commonly employed in cardiac catheterization, Percutaneous
Transluminal Coronary Angioplasty (PTCA), renal dialysis, hemodialysis, and extra-corporeal circulation
during bypass.

Performance Characteristics
The typical performance data summarized below was collected in health care facilities by health care
professionals trained in the use of the i-STAT System and comparative methods. All data uses the
PREWRM calibration, unless otherwise noted.

Precision data were collected at Abbott Point of Care Inc. and during clinical trials following a protocol
recommended by i-STAT and using plasma control material. Similar results can be expected in future
performance studies provided the same experimental design and data analysis procedures are followed.

Plasma Control

n

Mean

SD

%CV

Level 1

329

221 seconds

18 seconds

8.1

Level 2

438

456 seconds

22 seconds

4.8

«
...
476
477
478
479
480
...
»

Содержание i-STAT 1



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i-STAT 1

Бренд: i-SENS Страницы: 3

Бренд: GE Страницы: 35

Бренд: GE Страницы: 41

Бренд: A. Menarini Diagnostics Страницы: 50

Бренд: Accu-Chek Страницы: 294

Nipro Premier alpha

Бренд: i-SENS Страницы: 33

Бренд: IBP Страницы: 200

ONETOUCH BASIC (WITH DATA PORT)

Бренд: Lifescan Страницы: 98

ONE TOUCH BASIC BLOOD GLUCOSE MONITORING SYSTEM

Бренд: Lifescan Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды