ABB IRB 930 Скачать руководство пользователя страница 109

Страница: 109 / 606

Note

Action

Remove and clean the pipe after the oil is
drained.

Note

There will be some oil left in the gearbox
after draining.

Tightening torque: 10 Nm

Refit oil plugs.

Filling oil into the axis-2 gearbox

Use this procedure to refill the gearbox with oil.

Refilling oil to axis-2 gearbox

Note

Action

WARNING

Handling gearbox oil involves several
safety risks, see

Gearbox lubricants (oil or

grease) on page 30

CAUTION

The gearbox can contain an excess of
pressure that can be hazardous. Open the
oil plug carefully in order to let the excess
pressure out.

xx2300000549

Open the upper oil plug.

Note

The lower oil plug has to be closed; other-
wise, the oil may leak before required oil
amount is filled.

Continues on next page

Product manual - IRB 930

109

3HAC086009-001 Revision: A

4 Maintenance

4.8.3 Changing oil, axis-2 gearbox

Continued

Содержание IRB 930































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IRB 930

Отзывы:

Похожие инструкции для IRB 930

Бренды по названию

Популярные бренды

ABB IRB 930, Руководство по эксплуатации продукта

Результаты поиска

Содержание IRB 930

Отзывы:

Похожие инструкции для IRB 930

Бренды по названию

Популярные бренды