ABB IRB 930 Скачать руководство пользователя страница 551

Страница: 551 / 606

Refilling oil to axis-2 gearbox

Note

Action

WARNING

Handling gearbox oil involves several
safety risks, see

Gearbox lubricants (oil or

grease) on page 30

CAUTION

The gearbox can contain an excess of
pressure that can be hazardous. Open the
oil plug carefully in order to let the excess
pressure out.

xx2300000549

Open the upper oil plug.

Note

The lower oil plug has to be closed; other-
wise, the oil may leak before required oil
amount is filled.

WARNING

Overfilling of gearbox lubricant can lead to
internal over-pressure inside the gearbox
which in turn may:

•

damage seals and gaskets

•

completely press out seals and
gaskets

•

prevent the robot from moving
freely.

Type of oil and total amount is detailed in

Technical reference manual - Lubrication
in gearboxes

Refill the gearbox with oil.

Note

The amount of oil to be filled depends on
the amount previously being drained.

CAUTION

Oil filling must be slow to make sure air
venting is fluent.

Continues on next page

Product manual - IRB 930

551

3HAC086009-001 Revision: A

5 Repair

5.8.2 Replacing the axis-2 gear unit sub-assembly

Continued

Содержание IRB 930































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IRB 930

Отзывы:

Похожие инструкции для IRB 930

Бренды по названию

Популярные бренды

ABB IRB 930, Руководство по эксплуатации продукта

Результаты поиска

Содержание IRB 930

Отзывы:

Похожие инструкции для IRB 930

Бренды по названию

Популярные бренды