manualshive.com logo in svg

ABB i-bus EIB, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus EIB Скачать руководство пользователя страница 58

ABB i-bus

®

 EIB / KNX 

Project design and programming

 

 

4.5.8 Communication 

objects 

 

4.5.8.1 

Overview of the 
objects 

Objects for the “Master” function  

No  Function 

Object name 

Data type 

Flags 

0/15 

Control value heating 

Output A, Master 

1 byte (EIS6) 

CW 

The heat output is preset by the room thermostat via this object.  

1/16 

Control value cooling 

Output A, Master 

1 byte (EIS6) 

CW 

The cooling capacity is preset by the room thermostat via this object. 

2/17 

Speed limitation 

Output A, Master 

1 bit (EIS1) 

CW 

Used to limit the fan speed to a maximum value. 

3/18 

Forced operation 

Output A, Master 

1 bit (EIS1) 

CW 

Sets a fixed fan speed and valve position for the fan coil controller and disables them  

4/19 

Toggle heating/cooling 

Output A, Master 

1 bit (EIS1) 

CW 

In the operating mode “2-pipe system, heating and cooling”, it gives the fan coil controller the 
information about whether hot or cold water is being supplied.  

5/20
6/21
7/22
8/23 

Slave fan speed 2 
Slave fan speed 3 
Slave fan speed 3 
Slave fan speed 5 

Output A, Master 

1 bit (EIS1) 

CRT 

The master output controls further outputs via these objects which are used to control the 
ventilation. 

9/24 

Slave valve 

Output A, Master 

1 bit (EIS1) 

CRT 

Visible when controlling a 2-pipe system. Via these objects, the master controls a slave 
output which in turn controls the valve.  

9/24 

Slave valve heating 

Output A, Master 

1 bit (EIS1) 

CRT 

Visible when controlling a 4-pipe system. Via these objects, the master controls a slave 
output which in turn controls the valve for the heating circuit.  

10/25 

Slave valve cooling 

Output A, Master 

1 bit (EIS1) 

CRT 

Visible when controlling a 4-pipe system. Via these objects, the master controls a slave 
output which in turn controls the valve for the cooling circuit. 

11/26 

Telegr. fault thermostat 

Output A, Master 

1 bit (EIS1) 

CT 

Indicates a possible fault of the room thermostat. The fan coil controller is in the safety 
position.  

12/27 

Status switch 

Output A 

1 bit (EIS 1) 

CT 

This object reports the current state of the output.  

29 

Telegr. status byte 

Output A...B 

1 byte (non EIS) 

CRT 

This object provides further information about the operating state of the device (only 
Electronic Switch Actuator Modules ES/M 2.x.1). 

 

Object for the “Slave” function 

No  Function 

Object name 

Data type 

Flags 

0/15 

Fan coil slave 

Output A 

1 bit 

CW 

This object is used to control the output via the master. 

 

© 2004 ABB STOTZ-KONTAKT GmbH 

 

58

 

Содержание i-bus EIB































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды