manualshive.com logo in svg

ABB i-bus EIB, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus EIB Скачать руководство пользователя страница 28

ABB i-bus

®

 EIB / KNX 

Project design and programming

 

 

4.3.3 Parameter 

window: 

“Time” 

The time functions such as the staircase lighting function, ON/OFF delay 
and flashing can be set here. The parameter window is enabled under  
“A: Function”. 

Explanations about the time functions can be found in section 3.2.1. Please 
note the function diagram in section 3.2.6.  

Parameter: “Time function” 

This parameter defines the type of the time function. It is possible to choose 
between three types: “Staircase lighting”, “ON/OFF delay” and “Flashing”.  

Selection: “Staircase lighting function” 

 

The staircase lighting is switched on via an ON telegram. The staircase 
lighting time is started when the function is activated. It is switched off when 
the staircase lighting time elapses. 

Parameter: “Duration of staircase lighting” 

The operating time defines how long the staircase lighting is switched on 
after an ON command. 

Parameter: “Extending staircase lighting by multiple operation 
(‘pumping up’)” 

If a further ON telegram is received during the staircase lighting time, the 
remaining staircase lighting time can be extended by a further period. The 
maximum period can be set in this parameter.  

In the setting “no”, the staircase lighting is reset on receipt of an ON 
telegram (“retrigger function”). 

Parameter: “Staircase lighting can be switched off” 

It can be set here whether the staircase lighting is switched off prematurely 
by an OFF telegram (“yes”) or whether the OFF telegram is ignored during 
the staircase lighting time (“no”).  

Note:  

If the parameter value is “yes”, the staircase lighting can also be 
switched off via the following other objects, if they lead to a 
disconnection: “Logical connection”, “Preset”, “Lightscene”, 
“Disable”, “Permanent ON”, “Forced operation”.  

© 2004 ABB STOTZ-KONTAKT GmbH 

 

28

 

Содержание i-bus EIB































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды