manualshive.com logo in svg

ABB i-bus EIB, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus EIB Скачать руководство пользователя страница 48

ABB i-bus

®

 EIB / KNX 

Project design and programming

 

 

4.4.5 Parameter 

window: 

“Valve purge” 

Regular purging of a heating valve can prevent deposits from forming in the 
valve area and restricting the valve function. This is particular important at 
times when the valve position does not change very much. The valve is 
opened to the maximum during a valve purge. It can be triggered via the 
object “Trigger valve purge” and/or automatically at adjustable intervals.  

 

Parameter: “Time of valve purge”  

The duration of a valve purge is set here.  

Parameter: “Automatic valve purge” 

If “yes” is entered in this parameter, the valve is automatically purged at 
adjustable intervals. 

Parameter: “Period between valve purges” 

This parameter is visible for automatic valve purging. It defines the interval 
between two valve purges.  

 

© 2004 ABB STOTZ-KONTAKT GmbH 

 

48

 

Содержание i-bus EIB































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды