ABB i-bus EIB Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 62

ABB i-bus EIB Скачать руководство пользователя страница 39

ABB i-bus

®

EIB / KNX

Project design and programming

Additional function “Logic”

No Function

Object name

Data type

Flags

10/25
11/26

Logical connection 1 and
Logical connection 2

Output A

1 bit (EIS1)

CW

For logic operation of the object “Switch”. The logic function can be parameterised.

Additional function “Priority/forced operation, cyclic monitoring”

No Function

Object name

Data type

Flags

12/27

Priority / forced
operation

Output A

1 bit (EIS1) or
2 bit (EIS8)

CW

Sets the output to a defined state and disables it. Once the forced operation has finished, the
output reverts to the state that would have been set without forced operation.

Additional function “Threshold value”

No Function

Object name

Data type

Flags

13/28

Threshold value

Output A

1 byte (EIS6)
or
2 byte (EIS5)

CW

If the object value exceeds a parameterisable threshold value, a switching operation can be
executed.

4.3.9.2

Detailed description of
the objects

Object: “Switch”: 1 bit (EIS1)

Switches the output on and off (switching command). If the output is
parameterised as a “Normally open contact”, the relay is closed with the
telegram value “1” and opened with the telegram value “0” (when
parameterised as a “Normally closed contact”, the reverse process is carried
out).

Object: “Status switch”: 1 bit (EIS1)

Indicates the current state of the output. It can be inverted via the
parameters.

Standard:

Telegram value

“0”

Relay is opened

“1”

Relay

is

closed

Inverted:

Telegram value “0”: Relay is closed

“1”: Relay is opened

The object is visible if the parameter

“Status response of switching state”

is

set to “yes”. It is sent when there is a change in the value.

Note:

This object may have a wrong value after supply voltage failure,
if the output is parameterized to “unchanged” after bus voltage
failure as well as after bus voltage recovery.

© 2004 ABB STOTZ-KONTAKT GmbH

39

«
...
37
38
39
40
41
...
»

Содержание i-bus EIB































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды