manualshive.com logo in svg

ABB i-bus EIB, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus EIB Скачать руководство пользователя страница 43

ABB i-bus

®

 EIB / KNX 

Project design and programming

 

 

4.4 Operating 

mode: 

“Heating actuator” 

The function “Heating actuator” switches an electronic relay which is 
generally used to control an electrothermal valve drive. The device is 
normally controlled by a room thermostat. Various types of control are 
possible (e.g. continuous-action control).  

4.4.1 Parameter 

window: 

“General” 

 

Parameter: “Connected valve type” 

It can be set in this parameter whether a valve should be controlled as 
“normally closed” or “normally open”. If the valve is normally closed, the 
OPENING of the valve is achieved via the closing of the relay. If the valve is 
normally open, the OPENING of the valve is achieved by the opening of the 
relay.  

Parameter: “Reaction on supply voltage failure” 

On failure of the supply voltage, the Room Controller has no function. The 
output can be set to a defined state with this parameter.  

This parameter is only visible for the Switch Actuator Module SA/M 2.6.1. 
The Electronic Switch Actuator Modules ES/M 2.xx.1 always switch off on 
failure of the supply voltage (high-resistance).  

Parameter: “Control telegram is received as” 

The heating actuator can either be controlled via the 1-bit object “Switch” or 
the 1-byte object “Control value (PWM)”. 

In 1-bit control, the heating actuator functions in a similar way to a standard 
switch actuator: The room thermostat controls the heating actuator via 
standard switching commands. A 2-step control or pulse width modulation of 
the control value can be implemented in this way.  

For 1-byte control, a value of 0..255 (corresponds to 0%..100%) is preset by 
the room thermostat. This process is also known as “continuous-action 
control”. The valve is closed at 0% and fully opened at 100%. The heating 
actuator controls intermediate values via pulse width modulation (see 
diagram above).  

© 2004 ABB STOTZ-KONTAKT GmbH 

 

43

 

Содержание i-bus EIB































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды