manualshive.com logo in svg

ABB i-bus EIB, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus EIB Скачать руководство пользователя страница 24

ABB i-bus

®

 EIB / KNX 

Application and planning

 

 

3.5 Reaction 

on 

voltage 

failure and recovery 

Reaction on bus voltage failure 

It is possible to parameterise the behaviour of the outputs on failure of the 
bus voltage. The function of the Room Controller is retained provided that 
the supply voltage (115 / 230 V AC or 12 V DC auxiliary voltage) is available. 

If it has been set in the parameters, the Room Controller can thus continue 
to keep the functions in the room maintained.  

In the “Heating actuator” operating mode, any neutral position of the valve 
can be triggered. In the “Fan coil control” operating mode, the master and 
slave outputs are switched off (high-resistance). Fan speed 0 is thus 
triggered.  

Example:   Conventional push buttons are connected to a Room Controller 

via binary input modules. The Room Controller controls the 
lighting in the room. On bus voltage failure, the lighting can still 
be operated because the Room Controller is not supplied by the 
bus.  

Reaction on bus voltage recovery 

The behaviour of the outputs can be parameterised. In the master “Fan coil 
control” function, the outputs remain switched off until a new control value is 
received. 

Reaction on supply voltage failure 

The supply voltage has failed if both the 115/230 V AC supply and the 12 V 
DC auxiliary supply have failed. The Room Controller has no function in this 
case.  

For the 

Switch Actuator Module SA/M 2.6.

1, the status of the relay outputs 

can be parameterised so that a defined state can be established. The setting 
is carried out in the parameter “Reaction on bus voltage failure”. 

In the “Heating actuator” operating mode, it can be set whether the valve 
should be fully open or closed during the supply voltage failure. In the “Fan 
coil control” operating mode, the master and slave outputs are opened. Fan 
speed 0 is thus triggered. 

For the 

Electronic Switch Actuator Modules ES/M 2.230.1 and ES/M 2.24.

1, 

the outputs always switch off during the supply voltage failure (high-
resistance).  

Note:  

The preset and scene values that have been changed by the 
user are lost on failure of the supply voltage. They are 
overwritten by the parameterised default values.  

Reaction on supply voltage recovery 

The behaviour of the outputs is identical to the behaviour on recovery of the 
bus voltage. It can be parameterised for each output (except for fan coil 
control).  

3.6 Reaction 

after 

programming 

After programming, the device behaves in the same way as after bus voltage 
recovery (parameterisable). 

 

© 2004 ABB STOTZ-KONTAKT GmbH 

 

24

 

Содержание i-bus EIB































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды