manualshive.com logo in svg

ABB i-bus EIB, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus EIB Скачать руководство пользователя страница 52

ABB i-bus

®

 EIB / KNX 

Project design and programming

 

 

4.5.2 Parameter 

window: 

“General” 

 

Parameter: “Function of output when control is active” 

It can be set here whether the output operates as a “Master” or “Slave” in fan 
coil control mode.  

There can only be one output with the master function per fan coil unit. This 
output controls fan speed 1. The master controls valve drives or further fan 
speeds via communication objects. These outputs must then be 
parameterised with the “Slave” function.  

Note:

  

Outputs with the slave function should be parameterised as 
such. If parameterised e.g. as a “Switch actuator”, there is the 
danger that more than one output is closed under unfavourable 
conditions. The fan motor for example can be damaged as a 
result.  

Outputs with the slave function are only controlled via the object “Fan coil 
slave”. The following parameters are only visible in the “Master” setting. 

Parameter: “Status response of switching state” 

The object “Status switch” can be enabled via this parameter if the status of 
the output is reported on the bus. 

Parameter: “Waiting time for switching between two speeds” 

The operating time is delayed to enable an idle period when switching over 
the motor or valve or to prevent the period that they are switched on/off from 
being too short. The value range can be set between 500 ms and 1 min. 

Parameter: “Type of fan coil unit” 

It is possible to choose the type of fan coil unit. 

In a two-pipe system, only hot or cold water flows through the fan coil unit 
and the device therefore only has one heat exchanger. In a 4-pipe system, 
the fan coil unit has separate connections for hot and cold water. The device 
therefore has two heat exchangers. 

Parameter: “Operating mode” 

A two-pipe system can be used for “heating”, “cooling” or both “heating and 
cooling”. In latter case the object "Toggle heating/cooling" is released, over 
which the building control indicates whether hot or cold water is fed.  

© 2004 ABB STOTZ-KONTAKT GmbH 

 

52

 

Содержание i-bus EIB































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды