ABB DressPack IRB6650S Скачать руководство пользователя страница 296

Страница: 296 / 390

Note

Action

DANGER

Make sure all safety requirements are met when
performing the first test run. These are further
described in

Check of protective sleeve

The protective hose is protected against wear in exposed areas with a protective
sleeve.

Note

Action

xx1400000224

In order to be sure that the protective sleeve is in
the correct position, check the position after some
hours running.

If the protective hose is worn somewhere, adjust
the position of the protective sleeve.

296

Product manual - DressPack/SpotPack IRB 6650S

3HAC055424-001 Revision: C

4 Repair

4.2.11 Replacing the cable package IRBDP MH6 UI and IRBDP SW6 UI LeanID

Continued

Содержание DressPack IRB6650S






































































































































































































































































































































































































Результаты поиска

Содержание DressPack IRB6650S

Отзывы:

ABB DressPack IRB6650S, Руководство по эксплуатации продукта, Страница: 296 / 390

Результаты поиска

Содержание DressPack IRB6650S

Отзывы: