AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 9 / 104

background image

9

FIRE,  EXPLOSION  OR  CARBON
MONOXIDE POISONING HAZARD

Failure  to  replace  proper  controls
could  result  in  fire,  explosion  or
carbon monoxide poisoning. Failure to
follow  safety  warnings  exactly  could
result  in  serious  injury,  death  or
property damage. Do not store or use
gasoline  or  other  flammable  vapors
and  liquids  in  the  vicinity  of  this
appliance.

WARNING

Electric

shock

hazard.

Before

servicing, shut off all electrical power
to

the

unit,

including

remote

disconnects, to avoid shock hazard or
injury from rotating parts. Follow
proper Lockout-Tagout procedures.

WARNING

During installation, testing, servicing,
and troubleshooting of the equipment
it may be necessary to work with live
electrical

components.

Only

a

qualified

licensed

electrician

or

individual properly trained in handling
live

electrical

components

shall

perform these tasks.

Standard

NFPA-70E,

an

OSHA

regulation  requiring  an  Arc  Flash
Boundary  to  be field  established  and
marked  for  identification  of  where
appropriate

Personal

Protective

Equipment (PPE) be worn, should be
followed.

WARNING

GROUNDING REQUIRED

All  field  installed  wiring  must  be
completed  by  qualified  personnel.
Field installed wiring must comply with
NEC/CEC,  local  and  state  electrical
code  requirements.  Failure  to  follow
code  requirements  could  result  in
serious injury or death. Provide proper
unit ground in accordance with these
code requirements.

WARNING

VARIABLE FREQUENCY DRIVES

Do  not  leave  VFDs  unattended  in
hand  mode  or  manual  bypass.
Damage  to  personnel  or  equipment
can occur if left unattended. When in
hand  mode  or  manual  bypass  mode
VFDs  will  not  respond  to  controls  or
alarms.

WARNING

Electric motor over-current protection
and  overload  protection  may  be  a
function  of  the  Variable  Frequency
Drive  to  which  the  motors  are  wired.
Never defeat the VFD motor overload
feature. The overload ampere setting
must not exceed 115% of the electric
motors  FLA  rating  as  shown  on  the
motor nameplate.

CAUTION

«
...
7
8
9
10
11
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: Yard Machines Страницы: 16

Бренд: Trane Страницы: 68

Бренд: Lindab Страницы: 13

Бренд: SystemAir Страницы: 63

MILLENNIUM YCAS0230

Бренд: York Страницы: 168

Бренд: The Handy Страницы: 12

Бренд: McQuay Страницы: 99

Бренд: AERMEC Страницы: 17

Бренд: Dome Страницы: 14

Бренд: EarthQuake Страницы: 28

EasyFresh Next L

Бренд: irinox Страницы: 38

Бренд: F.F. Group Страницы: 84

Бренд: IV Produkt Страницы: 15

Pegasus PG100HC-2

Бренд: Skope Страницы: 24

Бренд: Yard-Man Страницы: 11

Бренд: RC GROUP Страницы: 48

Бренд: Yard Machines Страницы: 24

Бренд: Poulan Pro Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды